Civil Survey Instruments

Product Details:

For determining the liquid limit of soils. This is specially useful to obtain reliable and accurate results of those soil which have low plasticity index. The percentage moisture contents determined when cone with half angle of 15-30 minutes under a total sliding weight of 148 gm penetrates 25mm gives the liquid limit

Product Details:

We are offering Digital Temperature and Humidity Control to our clients.

Specification:

• Measures humidity between 0% to 99%
• Control accuracy to 0.1 degree/ 0.1% RH
• Support 12v working voltage
• Sized around 70x70x30mm

Product Details:

Dumpy Level DL-9 Imported Type Deluxe Model fitted with Erected Image System Special Blue Coated High Range Lenses, Acrometic Eyepiece in Fibre ABS Plastic Deluxe Box in Powder Coated Aluminium Tripod Stand in Cover.

Product Details:

Application Examples

cement clinker, chemicals, coffee, construction materials, fertilizers, fillers, flours, grains, metals powders, minerals, nuts, plastics, sand, seeds, soils, washing powder, ...

Product Advantages

• NEW: digital display of performance and time
• suitable for dry and wet sieving
• excellent separation efficiency even with short sieving times
• efficient electromagnetic drive
• 3-D throwing motion which ensures optimum use of the open sieve area and lets the sample move equally over the whole sieving surface
• sieve stack up to 510 mm height
• free adjustment of all process parameters (time, performance)
• optional comfort clamping device
• optional evaluation software EasySieve
• maintenance-free
• easy operation, ergonomic design

Product Details:

The Test is applicable to hot mix designs using bitumen and aggregates up to a maximum size of 25mm.  In this method, the resistance to plastic deformation of cylindrical specimen of bituminous mixture is measured when the same is loaded at periphery at 5cm per min.  This test procedure is used in designing and evaluating bituminous paving mixes.  The test procedure is extensively used in routine test programmers for paving jobs.  These are two major features of the Marshall Method of designing mixes namely:

 

a) Density – Voids Analysis

b) Stability – Flow Tests

 

The Marshal Stability of mix is defined as a maximum load carried by a compacted specimen at a standard test temperature of 60ºC.  The flow value is deformation the Marshall test specimen undergoes during the loading upto the maximum load, 0.25mm units.  In this test  attempt is made to determine optimum binder content for the type of aggregate mix and traffic intensity.

 

The Apparatus consists of :

v  A loading unit motorized, capacity 5000kgf with two telescopic pillars and an adjustable cross head.  Limit switches are fitted inside to control upward or downward movement of the pillars.  On off reversing switch and indicator lamps are on the front side while a hand wheel to manually move the pillars is on the right.  The load frame has fixed speed of 5.80cm per minute, operated on 230 volts AC.

v  One number Compaction pedal with specimen mould holder.

v  2 Nos Compaction Rammers, 4.5kg weight and free fall 45.7cm.

v  One number Breaking head assembly with provision to fix flowmeter.

v  3 Nos Specimen Mould 10.16cm I.D. x 7.6cm high with base plate and extension collar.

v  One number Kit for specimen extraction, consists of one each load transfer bar, steel ball, specimen extracting plate.

v  Integral type Proving Ring capacity 5000 kgs.

v  A dial gauge 0.01 x 25mm

 

Marshal stability test apparatus with accessories 100mm

Marshal stability test apparatus with accessories 150mm

Product Details:

Product Description

We have earned vast credibility in the market for offering Concrete Permeability Test Apparatus. Due to high demand, we present these products at reasonable costs.

 

Features:

 

• Sturdy construction

• Flawlessly finished

• Low maintenance

• Widely used

• Technically accurate

Product Details:

The apparatus consists of water bath with a thermostatic heater and a circulating pump to maintain uniform water temperature. One half of the briquette moulds is fixed in a fixed plate in the water bath, the other half of the briquette mould is fixed to a carrier which slides over a rotating threaded shaft with a clutch. The motor and gears to rotate the shaft are housed in a cabinet fixed above the other end of the both. A pointer fixed to the carrier moves over. a scale graduated from 0-110 cm x 1mm fixed on the bath with "0" (Zero) of the scale towards the fixed plates side. The rotating shaft has 2 speeds of travel for the bracket, 5 cm/min. and 1cm/min. selected by a clutch. Water bath inside is of Stainless steel with insulation and a water drain. A heater with thermostatic control is fitted. inside the water bath. Control switches for motor, stirrer, heater and indicator lamps are fitted to a control panel located at a convenient place on the water bath. Complete with three briquette moulds and one base plate. Working on 230 Volts, single phase, 50 cycles, AC.

Product Details:

Torsion Testing Machine is designed for conducting Torsion and twist tests on various metal wires, tubes, sheet materials. Torque measurement is by Pendulam Dynameter System. Torque ranges can be adjusted. Torque can be applied to specimen by geared motor through gearbox. Autographic recorder can be provided to know relation between torque and angle of twist on specific request. The Accuracy of the torque indication 1% of the true torque.

Product Details:

Mastic Hardness Tester For Bitumen

For determining the hardness number of Mastic Asphalt for flooring. It consist of an internally insulated cabinet to the base of which is fitted a water bath having two taps. The bath is heated by an immersion heater and the temperature is controlled with the thermostat at 35° +/- 0.5° C. A 6.5mm dia pin is loaded on the specimen by means of a lever to give a 31.7 Kg weight. A dial gauge
0.01 x 25 mm is provided to record the penetration of pin into the specimen. 

Product Details:

This is used for determination of resistance to wear for cement concrete flooring tiles.  Tiles specimen of size 7.06cm x 7.06cm is pressed tace wise under specific load on a grinding path and abrasive powder is evenly spread on the rotating grinding path and after specific number of revolutions of the grinding disc the second parallel side of the tile is subjected to wear for similar under of rotations.  The wear of the tile is measured on a thickness gauge specifically made for the purpose.  The machine consists of a disc rotating at a speed of 30 rpm in a circular tray.  A bracket is provided to hold the specimen.  A counter balance lever loads the specimen.  Load applied is 30kgf.  A funnel is fitted to evenly spread abrasive powder on the grinding path.  A pre-set counter automatically stops the machine after 22 revolutions.  This counter is re-adjustable.  The machine works on 440 volts AC, 3 phase electrical supply.

Product Details:

 

• Used in Flow-time determination for Self-Consolidating Concrete (SCC)
•  Out flow orifice is equipped with a valve that can be openned momentarely
•  Supplied with bucket

TECHNICAL SPECIFICATIONS

• Made of stainless steel
• Stand-mounted

Product Details:

The Equipment consists of a circular base with two vertical guides.  The hammer of weight 13.75 ± 0.25kg can be raised to fall freely down the vertical guides.  The height of fall can be adjusted through 380 ± 5mm.  The hammer is provided with a locking arrangement.  The hammer falls freely to the base and is removable for emptying.  Supplied complete with metal measure 75mm dia x 50mm high and tamping rod 230mm long x 10mm dia with/without blow counter.

Product Details:

We are offering Seed Sieves to our clients.

Feature:

• Rugged design
• Lightweight
• Corrosion resistant

 

Specification:

 

• Weight: As per requirements
• Material: Stainless Steel
• Power(W): 0.5kw

Product Details:

Concrete Moulds are easily cast by using a tamping bar or a vibrating table.  However air trapped in cement mortar paste can not be thus removed while casting cement mortar moulds.  Easy method is to impart greater vibration of lesser amplitude to the mould while casting.  This is achieved in a Vibrating Machine.  Vibrating Machine is used for the preparation of mortar cubes for the determination of compression strength of ordinary and rapid hardening Portland cement, low heat Portland cement, Portland blast furnace cement and high alumina cements.

 

Specifications: 
The machine consists of a vibrating frame assembly and an electric motor mounted on a sturdy base.  The complete frame assembly consists of a vice to hold a 7.06cm cube mould and two studs threaded at top and a hopper to feed the sample in the mould.  This assembly is supported on four springs and has an in built rotating shaft which rotates eccentrically and thus imparts vibrations to the entire frame.  A balance weight is an integral bottom part of the frame.  The centre of gravity of the assembly is brought to the centre of the eccentric shaft or within a distance of 25mm below it.  The electric motor drives the shaft of the frame and thus imparts required vibrations to the mould.  The frequency of vibration is 12000 ± 400 vibration per minute.  Supplied complete with a 7.06cm cube mould and loose base plate, a time switch 0-5mins x 1 min and certificate of vibration.

Product Details:

We are offering Cross Line Laser Level Rotary to our clients.

Features:

• Dimensionally accurate
• Impact resistant
• Highly accurate and easy to use
• 160°Laser Range
• Impact-Resistant ABS Housing
• Size Fits in Toolbox or Tool Belt
• High-Intensity Laser for Visibility in Varying Lighting Conditions
• Three-Vials Measure Level, Plumb, 45°
• Magnetic Base Mounts to Pipes, Metal Studs, and Drop Ceiling Framework
• Complete with Adjustable Tripod
• Working Range: up to 160 feet
• Turn the button up when use the laser point
• Turn the button down when use the cross point

Specifications:

• Cross Line Laser Level/Rotary Laser Tool/Measuring Tool With Tripod
• Material: ABS
• The length: 18cm (7 inches)
• Laser: Class II less than 1mw, Class IIIA less than 5mw
• Wavelength: 650mm
• Working distance: 50m
• Accuracy: 0.05mm
• Laser Accuracy: ±2/3" @ 50'
• Level Vial Accuracy: ±2/3" @ 50'
• Laser Output: <3mW
• Power supply: 2XAAA batteries

Package included:

• 1x Laser Levels
• 1x Adjustable Tripod

Product Details:

The apparatus is used for the laboratory determination of permeability of soils using a constant or a variable head. This test is recommended for soils with coefficient of permeability in the range of 10 to 10 cm/sec. The maximum particle size of the soil which can be tested in the mould is 10mm.

 

Specifications :

The equipment comprises one each:

• Gun Metal Mould, 100mm I.D. x 127.3mm high x 1000 ml. volume
• Gun Metal Mould extension collar, 100mm dia x 60mm high for the above mould
• Gun Metal Drainage base plate with a recess for a porous stone and with an outlet valve.
• Metallic Clamping Ring
• Gun Metal Drainage cap (Top plate with a recess for a porous stone and fitted with an inlet valve and an air release valve)
• Gun Metal dummy plate to serve as a false bottom during compaction
• Porous stone for drainage cap
• Porous stone for base plate
• Set of glass stand pipes approximately 6mm dia, 10mm dia and 20mm dia mounted on a wooden board.
• Overhead Tank, made of steel, approximately 38cm dia x 1 meter high provided with an arrangement to indicate the water level.
• Rammer 2.6kg x 310mm controlled fall
• Rammer 4.89 kg x 450 mm controlled fall

Product Details:

We are offering Laser Level Horizontal to our clients.

Feature:

• Can be set on tripod or a stable surface
• Designed for outdoor environments
• Extremely convenient for construction purposes
• 2 line laser level, it generates a horizontal line and a perpendicular line
• The bottom with a wall mouth, convenient to hang at any place
• 1.5 times light source, much brighter
• 360-degree rotation
• There is a bubble on the top to help adjust level

Description:

• TK-126 2 Line 1 Point Laser Level Horizontal And Vertical 360º Rotation Self-leveling Cross With Storage Bag

Specification:

• Light source: Semiconductor
• Diode power: 7mW
• Wavelength: 635nm
• Precision of vertical and horizontal: ±2.5mm/5M
• Time of stable equilibrium: <5 seconds
• Working temperature range: -5-45
• Dimension: 96 x 84 x 100mm
• Auto self-leveling range: ±3º
• Power supply: 2 x AA batteries(Not included)

Usage:

• Set the instrument on the tripod or a stable surface, adjust the instrument. If the instrument is too tilted, out of range (2 degrees), the laser tube will automatically turn off (or if audible alarm).
• Switch knob clockwise to open the instrument, emitting a laser beam.
• Turn the instrument, the laser beams toward goals.
• Gently adjust knob, find work orientation.
• When work is over, turn the switch knob counterclockwise, turn off the instrument.
• With light point designed outdoor environments, provide convenience for the construction.

Package included:

• 1 x Laser Level(Not include the battery)
• 1 x Storage Bag

Product Details:

It is used for compacting concrete cubes and cylinders.

 

Specifications: Sizes: 75cmx75cm 100cmx100cm. To carry out a load of 140kg.  The unit consists of a motor fitted with a variable pitch pulley housed in a cabinet.  The vibrations are imparted by means of off balance masses rotating on a shaft of a vibrator clamped to the underside of the table top.  The table top is 50cm x 50cm and has stops along its edges to prevent moulds form walking off the table during vibration. A cross arm adjustable on a vertical rod at the centre of the table is provided to hold the moulds while operating the table.  The variable pitch pulley arrangement permits the frequency to be varied step Lesley between a maximum of 3600 vibrations down to 2600 vibrations per minute.  A speed regulation handle is provided for increasing or decreasing the frequency a switch is provided for starting the motor.  Suitable for operation on 440 Volts, 3 phase, 50 cycles, A.C.Supply.

SIZES:-

Vibrating Table 1 MTR. 

Product Details:

This product has contributed a lot to the construction works under governmental and non-governmental authorities.

 

Product Description : This apparatus is designed with an air tight flanged cylindrical bowl, which is available with the following capacities- 0.005, 0.007, 0.01 cubic meters.

Capacity Are Available 
Bowl Capacity: 0.005 cubic meter
Bowl Capacity: 0.007 cubic meter
Bowl Capacity: 0.01 cubic meter
Bowl Capacity: 0.01 cubic meter

Specification:

• The cylinder of the device is designed to be air pressure tight. The tight hold is captured within a bowl.
• The bowl has been fixed with the conical cover assembly and blocked with a seal.
• An air valve is designed on the conical cover and there is also a petcock for flowing off the water from there.
• The fixed air content is applied on the conical cover, which has a pressure bulb. The applied pressure is counted and recorded on the pressure gauge.
• The entire unit of the device is established on a flat base.

Product Details:

It is designed for finding out the deformation and strains on 15cms. Diameter and 30 cms. High cement concrete cylinders when subjected to compressive loads. 

Product Details:

This instrument is used for determination and checking of bitumen percentage in bituminous mix, the mix is added with a Solvent and dissolved bitumen is removed by centrifugal action. Consists of a removable aluminum rotor bowl, capacity 3000gms. This shaft and thus the bowl is rotated fast manually by enclosed gears in the cast body and handle. Solvent is introduced during the test through the holes in the cap of the 

 

Product Details:

HIGH-QUALITY, DURABLE CONSTRUCTION. Measuring 12" in diameter with a 3' circumference, this unit boasts a plastic molded wheel for long-lasting strength and use. It features a telescoping handle that is extendable up to 44 inches and collapses to 27 inches for easy carrying and storage in the included soft carrying case. The kickstand is sturdy and all buttons are water-proof and dust proof, ensuring that this unit is built to last. METRIC / Inch MEASURING UNITS. The Digital Measuring Wheel measures in units of tenths of inch or meters up to a 9,99.9 inch/meter range, providing the added convenience of calculating mixed measurements on one project if needed.

Brand : V Tech

Type : Multiple Unit Measuring Wheel

Operation Type : Electronic

Display Type : Digital

Foldable : Yes

Brake Included : No

Distance Measured : 9999.99 m

Measurement Unit Type : Meter, Foot

 

 

Dimensions

 

Wheel Diameter : 300 mm

 

Weight : 1 kg